Getting Started Guide

The getting started is broken up into the following sections:

• Getting Started on the ESP32 platform

• Getting Started on the STM32 platform

• Getting Started on the Generic UNIX platform

Getting Started on the ESP32 platform

The AtomVM virtual machine is supported on the Espressif ESP32 platform, allowing users to write Erlang and Elixir programs and deploy them to the ESP32 micro-controller.

These instructions cover how to get the AtomVM virtual machine flashed to your ESP32 device, as well as how to flash your Erlang and Elixir programs that will be executed by the virtual machine running on the device.

For most applications, you should only need to install the VM once (or at least once per desired AtomVM release). Once the VM is uploaded, you can then begin development of Erlang or Elixir applications, which can then be flashed as part of your routine development cycle.

Requirements

Deployment of AtomVM applications requires the following components:

• A computer running MacOS or Linux (Windows support is not currently supported);

• An ESP32 module with a USB/UART connector (typically part of an ESP32 development board);

• A USB cable capable of connecting the ESP32 module or board to your development machine (laptop or PC);

• The esptool program, for flashing the AtomVM image and AtomVM programs;

• An Erlang/OTP release (21, 22, or 23);

• A serial console program, such as minicom or screen, so that you can view console output from your AtomVM application.

• (optional) For Erlang programs, rebar3;

• (optional) For Elixir programs, mix, which ships with the Elixir runtime;

Deployment Overview

The ES32 AtomVM virtual machine is an IDF application that runs on the ESP32 platform. As an IDF application, it provides the object code to boot the ESP device and execute the AtomVM virtual machine code, which in turn is responsible for execution of an Erlang/Elixir application.

The AtomVM virtual machine is implemented in C, and the AtomVM binary image contains the binary object code compiled from C source files, as well as the ESP boot loader and partition map, which tells the ESP32 how the flash module is laid out.

AtomVM developers will typically write their applications in Erlang or Elixir. These source files are compiled into BEAM bytecode, which is then assembled into AtomVM “packbeam” (.avm) files. This packbeam file is flashed onto the ESP32 device, starting at the data partition address 0x210000. When AtomVM starts, it will look in this partition for the first occurrence of a BEAM module that exports a start/0 function. Once that module is located, execution of the BEAM bytecode will commence at that point.

The following diagram provides a simplified overview of the layout of the AtomVM virtual machine and Erlang/Elixir applications on the ESP32 flash module.

|               |
+---------------+  ----------- 0x1000
+---------------+           |
| partition map |           | AtomVM
+---------------+           | binary
|               |           | image
|   AtomVM      |           |
|   Virtual     |           |
|   Machine     |           |
|               |           v
+---------------+  ----------- 0x210000
|               |           ^
|               |           |
|     data      |           | Erlang/Elixir
|   partition   |           | Application
|               |           |
|               |           v
+---------------+  ----------- end


Deploying an AtomVM application to an ESP32 device typically involved two steps:

1. Connecting the ESP32 device;

2. Deploying the AtomVM virtual machine;

3. Deploying an AtomVM application (typically an iterative process)

These steps are described in more detail below.

Connecting the ESP32 device

Connect the ESP32 to your development machine (e.g., laptop or PC) via a USB cable.

+---------------+
| laptop or PC  |
|               |           +-------+
|               | USB       |       |
|               x-----------x       |
|               |           |       |
|               |           +-------+
+---------------+           ESP32


Note. There are a wide variety of ESP32 modules, ranging from home-made breadboard solutions to all-in-one development boards. For simplicity, we assume a development board that can both be powered by a USB cable and which can be simultaneously flashed using the same cable, e.g., the Espressif ESP32 DevKit.

Deploying the AtomVM virtual machine

The following methods can be used to deploy the AtomVM virtual machine to an ESP32 device:

1. Flashing a binary image;

2. Building from source.

Flashing a binary images

Flashing the ESP32 using a pre-built binary image is by far the easiest path to getting started with development on the ESP32. Binary images contain the virtual machine image and all of the necessary components to run your application.

We recommend first erasing any existing applications on the ESP32 device. E.g.,

shell$esptool.py --chip esp32 --port /dev/ttyUSB0 --baud 115200 erase_flash ...  Note. Specify the device port and baud settings and AtomVM image name to suit your particular environment. Next, download the latest stable or nightly ESP32 release image from the AtomVM web site. Note. Nightly images may be unstable and may result in unpredictable behavior. Finally, use the esptool to flash the image to the start address 0x1000 on the ESP32. E.g., shell$ esptool.py --chip esp32 --port /dev/ttyUSB0 --baud 115200 \
--before default_reset --after hard_reset \
write_flash -u --flash_mode dio --flash_freq 40m --flash_size detect \
0x1000 atomvm-esp32-v0.1.0.bin
...


Once completed, your ESP32 device is ready to run Erlang or Elixir programs targeted for AtomVM.

Building from source

You may optionally build AtomVM from source and deploy the AtomVM virtual machine to your ESP32 device manually. Building AtomVM from source is slightly more involved, as it requires the installation of the Espressif IDF SDK and tool chain and is typically recommended only for users who are doing development on the AtomVM virtual machine, or for developers implementing custom Nifs or ports.

Instructions for building AtomVM from source are covered in the AtomVM Build Instructions

Deploying an AtomVM application

An AtomVM application is a collection of BEAM files, which have been compiled using the Erlang or Elixir compiler. These BEAM files are assembled into an AtomVM “packbeam” (.avm) file, which in turn is flashed to the main data partition on the ESP32 flash module, starting at address 0x210000.

When the AtomVM virtual machine starts, it will search for the first module that contains an exported start/0 function in this partition, and it will begin execution of the BEAM bytecode at that function.

AtomVM applications can be written in Erlang or Elixir, or a combination of both. The AtomVM community has provided tooling for both platforms, making deployment of AtomVM applications as seamless as possible.

This section describes both Erlang and Elixir tooling for deploying AtomVM applications to ESP32 devices.

Erlang Tooling

Deployment of AtomVM applications written in the Erlang programming language is supported via the atomvm_rebar3_plugin plugin, a community-supported plugin to the rebar3 Erlang build tool.

You can generate a simple application from scratch using the atomvm_rebar3_plugin template, as follows:

Edit or create the $HOME/.config/rebar3/rebar.config file to include the atomvm_rebar3_plugin plugin: %%$HOME/.config/rebar3/rebar.config
{plugins, [
{atomvm_rebar3_plugin, "0.3.0"},
...
]}.


In any directory in which you have write permission, issue

shell$rebar3 new atomvm_app <app-name>  where <app-name> is the name of the application you would like to create (e.g., myapp). This command will generate a rebar project under the directory <app-name>. The generated application will contain the proper rebar.config configuration and will contain the <app-name>.erl module, which exports the start/0 function with a stubbed implementation. Specifically, note the following stanza in the generated rebar.config file: %% rebar.config {plugins, [ {atomvm_rebar3_plugin, "0.3.0"}, ... ]}.  And note the myapp application exports a start/0 function, e.g., %% erlang -module(myapp). -export([start/0]). start() -> ok.  With this plugin installed, you have access to the esp32_flash target, which will build an AtomVM packbeam shell$ rebar3 esp32_flash --port /dev/ttyUSB0
===> Fetching atomvm_rebar3_plugin v0.3.0
===> Fetching rebar3_hex v6.11.3
===> Fetching hex_core v0.7.1
===> Fetching verl v1.0.2
===> Analyzing applications...
===> Compiling verl
===> Compiling hex_core
===> Compiling rebar3_hex
===> Fetching atomvm_packbeam v0.3.0
===> Analyzing applications...
===> Compiling atomvm_rebar3_plugin
===> Compiling packbeam
===> Verifying dependencies...
===> Analyzing applications...
===> Compiling myapp
===> AVM file written to : myapp.avm
===> esptool.py --chip esp32 --port /dev/ttyUSB0 --baud 115200 --before default_reset --after hard_reset write_flash -u --flash_mode dio --flash_freq 40m --flash_size detect 0x210000 /home/frege/myapp/_build/default/lib/myapp.avm


Note. Consult the the atomvm_rebar3_plugin plugin documentation, for more detailed information about how to use this tool.

Once the application has been flashed, you may connect to the ESP32 over the serial port using minicom, screen, or equivalent.

Elixir Tooling

TODO mix + https://github.com/atomvm/ExAtomVM + hex

Getting Started on the STM32 platform

TODO will se distribute a binary image for STM32?

Getting Started on the Generic UNIX platform

AtomVM may be run on UNIX-like platforms using the AtomVM executable.

You may specify one or more AVM files on the command line when running the AtomVM command. BEAM modules defined in earlier AVM modules on the command line take higher precedence that BEAM modules included in AVM files later in the argument list.

shell\$ AtomVM /path/to/myapp.avm


Currently, the AtomVM executable must be built from source.

See the AtomVM Build Instructions for instructions about how to build AtomVM on the Generic UNIX platform.

Where to go from here

The following resources may be useful for understanding how to develop Erlang or Elixir applications for the AtomVM platform: